Chiller's Hybrid SR-2

All about overclocking and modding techniques, how-to's and worklogs.

Moderator: CM Moderator

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Thu Mar 10, 2011 11:41 am

i'm going to fill up the loop now the 3th pump is installed, own mixture : 25% Ethylene Glycol and 75% PURE water, no demi.

what you see in the measure cup is the Glycol no color pure 100% glycol :

Image

here my koolanc poor in cup on the ZERN res with a snake connector to make it a little bit eassier to fill :

Image

on the drain valve i putted also a tube in a bus filled with my mixture, where the pump can draw it's liquid from when i put the valve open, to make it a little bit eassier to lol :

Image

Image

and here comes the first liquid lol, pumps are now running to get the last micro bubbles out the loop, for now, no leaks found :

Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Fri Mar 11, 2011 7:47 am

HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Sat Mar 12, 2011 4:13 am

It's a miracle !!!!

i get it closed hahahahaha, +200m cable in limited room of 3,5cm lol :

Image

here you see that the plate is a little round, but i put the cable fast fast in to look if i get it closed,
later on the cable will be nice routed and strapped so that the plate doesn't look round :

Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Sun Mar 13, 2011 4:53 am

last minute adjustment for the vga's :

Image

Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Mon Mar 14, 2011 11:15 am

little update :

Image

Image

Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Thu Mar 24, 2011 6:31 am

here are the load temps, cpu temp in Coolit software is not correct, cpu isn't supported by the coolit software.

As you see idle the coolers run lower power, when stressed the coolers will raise there cooling power, and keep the liquid temp low, under Ambient,
cpu temp raises a 5 a 6°C from idle to load thanks to temp controlled coolers.

Temp of liquid is set @ 22°C max, min power of coolers @ 60%, max power @ 100%, real nice settings on these coolers,
and the coolers don't even run at 100% to keep the temp, for me that's good for lower noise level :

Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Mon Mar 28, 2011 9:12 am

little sneakpeak what i'm doing now :Most of the time, people put there powercable for vga like the RED arrows.
I whant it as clean as possible in this case, en i will do my powercables like the GREEN arrow, straight horizontal with the vga's.
Vga's seems like they are floating in the air lol, strange sight.
On later time i can mod also the plastic cap on the vga, make it wider, little bit bigger, so the powercables are IN the plastic cap of the vga cooler, totally NOT visible.
Image
And this is the beginning of this little vga mod :
Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Sat Apr 02, 2011 11:07 am

Am working now on the last mem flames, did the cables in the backpanel better now, so the back-panel is not round anymore,
and made some led's for give light to the mem modules :

Image

Image

Image

Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Mon Apr 11, 2011 11:56 am

Killer2100 eifinally in the house,
original cover removed for modding it,
and here a pic of the killer2100 in operation with two red led's, what fits very good in the theme :

Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Fri May 06, 2011 9:22 am

Got a new sponsor, he send me already a nice package ;D

Thanks to Eddy of IT-Service

Image

Nice and good packed, and a triple sli connector also ?

There is already 1 can of Dr Pepper gone, girlfriend grabbed it !!! :o
Image

There was no Triple SLI connector in that box, but nice GOODY's !!!! :P

Image

Directly also cleaned the Pc room, and make the desk clear of any garbage and screws :

Image

The second mem kit of 12Gb 2000Mhz GT's got already new cooling fins of my own creation,
there are more happy now with the new ones ;) .

Image

the lowest modules have a red led on them for in the dark, but gives by day a different color,
but you can be shure, they have the same red, also the flashlight extra on it.......
Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Sat May 07, 2011 9:35 am

Got a new toy in the house, and tried to make nice pics of that 960Gb monsta and some nice pics in my case :

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Wed Jul 27, 2011 8:34 am

HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Tue Jan 17, 2012 9:20 pm

There's a new baby coming to me, a Evga GTX285 Classified 1Gb vga, just for PhysX in my rig :

Image

Image

then i will have all Classified stuf in it :

SR-2 Classified mobo
2x GTX580 Classified for FPS
SR-2 1200w Classified Psu
and the gtx285 Classified for PhysX

Image
Last edited by HybridChiller on Sat Jan 28, 2012 3:31 pm, edited 1 time in total.
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Sat Jan 28, 2012 9:39 am

Last stuf making for vga's, making 5 more of these, cut them on lenght, other side also connectors,
isolate them, make them black :

Image

Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

Re: Chiller's Hybrid SR-2

Postby HybridChiller on Sun Jan 29, 2012 8:20 am

like this the connectors will be :

Image

each vga 2 connectors, but behind each pair there are 3x 12v rails.
So vga's will get enough power
(and made shure the cables are not to tin for that power transfer)

Image

only those bars need to come at the same hight as the connectors on vga's, so need some curves to get that
(don't mind the dust lol) :

Image
HybridChiller
Aerogate Geek
 
Posts: 42
Joined: Tue Mar 01, 2011 6:30 am

PreviousNext

Return to Modding & Overclocking

Who is online

Users browsing this forum: No registered users and 1 guest

cron