00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Showcase your mods for the world to see!

Moderator: CM Moderator

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Mon May 02, 2011 8:05 pm

Proper fit for the unit and its harnesses
Attachments
44.JPG
44.JPG (104.99 KB) Viewed 2931 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Mon May 02, 2011 8:07 pm

Custom made brackets made to hold wires behind the hard drive bay
Attachments
45.JPG
45.JPG (76.9 KB) Viewed 2930 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Mon May 02, 2011 8:09 pm

and the back wall backets installed
Attachments
46.JPG
46.JPG (82.13 KB) Viewed 2934 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Mon May 09, 2011 6:42 pm

Where the front was,is now the right side door
Attachments
47.JPG
47.JPG (68.96 KB) Viewed 2843 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Mon May 09, 2011 6:45 pm

This door will hold a Cooler Master 200mm fan
Attachments
48.JPG
48.JPG (85.4 KB) Viewed 2847 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Mon May 09, 2011 6:58 pm

Here is the heavily modified Mother board tray. The upper right hole will allow the 8pin power wire to pass though.
The back originaly housed one 80mm exhaust fan. After cutting this area, it is just big enough to stack two 80mm fans now.
The large hole in the middle was cut to gain access to the back of the mother board to ease mounting of the processor.
The round holes were cut for ventilation and center the rear 200mm fan. The angles will be mounted on the back and will channel wire around the
fan. I also made an extension that will be attached to the right front. This extension will allow the main power harness, sata,
power switch, and video card cables to pass though for an ultra clean look. My goal is to hide as many wires as possible.
Attachments
49.JPG
49.JPG (76.61 KB) Viewed 2848 times
Last edited by d0g on Mon May 09, 2011 7:28 pm, edited 2 times in total.
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Mon May 09, 2011 7:08 pm

The tray facing front with the extention mounted on the right (more holes were drilled for the vc and switch)
Attachments
50.JPG
50.JPG (71.85 KB) Viewed 2838 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Mon May 09, 2011 7:09 pm

The back of the tray with angle mounted acting as conduits for harnesses
Attachments
51.JPG
51.JPG (78.47 KB) Viewed 2835 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Mon May 09, 2011 7:15 pm

The military grade mb. (no aluminum caps) look closely, not one.
I had two caps burst on me over the years. All boards should be made this way.
Attachments
52.JPG
52.JPG (153.8 KB) Viewed 2836 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Mon May 09, 2011 7:17 pm

The mb with the tray assembly
Attachments
53.JPG
53.JPG (110.82 KB) Viewed 2834 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Mon May 09, 2011 7:33 pm

Mother board mounted with I5. Here you can see the 8pin power cable, the first of many carbon fiber sleeved cables.
Attachments
54.JPG
54.JPG (142.18 KB) Viewed 2824 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Wed May 11, 2011 8:03 pm

Custom cut cpu and gpu temperature guages mount assembly
Attachments
55.JPG
55.JPG (79.02 KB) Viewed 2792 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Wed May 11, 2011 8:06 pm

Installed temp guages (the cpu will light blue, gpu green)
Attachments
56.JPG
56.JPG (127.5 KB) Viewed 2812 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Wed May 11, 2011 8:08 pm

Custom cut backet for rear fans exhaust assembly
Attachments
57.JPG
57.JPG (89.18 KB) Viewed 2792 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

Re: 00 InfiniTiS 00 - 2011 CM Case Mod Competition Entry

Postby d0g on Wed May 11, 2011 8:10 pm

Rear 80mm fans installed
Attachments
58.JPG
58.JPG (119.96 KB) Viewed 2807 times
d0g
Vortex Dreamer
 
Posts: 113
Joined: Sun Mar 27, 2011 1:40 pm

PreviousNext

Return to 2011 Case Mod Competition

Who is online

Users browsing this forum: No registered users and 1 guest